What we repair

Manufacturer authorized service for the full 4O3A Signature line

As the Manufacturer Authorized North American Service Center for 4O3A Signature, we repair their amplifiers, tuners, automation, switches, and filters to the manufacturer's own standards. Every evaluation is engineering-level: run on our automated, calibrated RF bench with AI-assisted analysis, and reviewed by an experienced RF engineer. Don't see your exact model? Ask us; if it's 4O3A, we service it.

Open-book parts pricing
Parts cost + inbound shippingcost
Standard markup× 1.25
Applicable tariffs / duties+ at cost
Labor$150/hr bench rate
Licensed hams$25/hr off → $125/hr
Shipping we buy for youat cost + 10%
Texas sales taxwhere it applies
Diagnostic fee$95, credited in full against an approved repair
Warranty on our work90 days from our ship date, parts and labor

Formula: ((parts + shipping) × 1.25) + tariffs. Every estimate itemizes parts and labor so you can see exactly where the money goes. The ham discount applies to hourly bench labor (not flat-rate repairs).

Honest by design

You always see the parts math

We don't hide markups or pad invoices. Parts are billed on a single published formula, tariffs pass through at cost, and labor is a clear bench rate - $150/hr, with $25/hr off for licensed hams ($125/hr). Estimates are itemized and require your approval before we proceed.

Sending us your unit

Shipping & packing

Your RMA number comes back the moment you submit a request; when we accept the request we email you these instructions. Please don't ship anything until then - the RMA slip in the box is how we match your unit to your ticket the moment it arrives.

  • Use the original container. It's built to protect the unit in transit. Don't have it anymore? Ask us - if it's in stock we'll ship you a replacement carton for a modest fee.
  • Leave the accessories at home. Unless we specifically ask for them, don't include power cords, cables, or manuals - just the unit itself.
  • Put your RMA slip in the box. Print it from your repair page once we accept your request; it comes filled in, and it goes inside the box with the unit.
  • Mark the box with your RMA number. Write it clearly on the outside of the carton.

Your repair page carries the printable RMA slip, with packing guidance, from the moment we accept your request - these instructions are the short version to keep handy.

Lightning & surge damage

Lightning damage assessment

Took a direct strike or a nearby hit? We assess and document the damage for you and your insurer. Most of the time we recommend replacement rather than repair. Here's why, and the one case where we do repair.

Lightning Damage Assessment

We inspect and test the unit, document the extent of lightning and surge damage with detailed findings and photos, and deliver a written assessment report. We routinely supply these assessments directly to insurance carriers to support claims, and the report gives you a clear basis for a repair-vs-replace decision.

Flat assessment fee · insurance-ready written report & photos
Repair policy

Why we rarely repair lightning-damaged units

A strike or nearby hit can drive enormous transient voltages and currents through a unit. The damage is often pervasive, latent, and impossible to fully detect on the bench:

  • Semiconductor junctions degraded just enough to test OK now but fail later.
  • Stressed solder joints and PCB carbonization that creates hidden paths.
  • Compromised dielectric in capacitors and transformers. Damaged relay coils and contacts.

Because we can't reliably find every fault a strike leaves behind, we won't repair a unit whose damage we can't bound. A unit like that could fail again under full power, damage other parts of your station, or become a safety hazard. The exception is a strike your protection stopped at the door. The protection operated, the damage stays in the parts it was there to sacrifice, and everything past it tests within specification. That is ordinary bench work, and we repair it. Your assessment report says which case your unit is.

Power Genius amplifiers

Amplifier repair

Legal-limit and commercial RF amplifiers - diagnosed under real load, with LDMOS, PA-stage, protection, cooling, and control-board faults addressed and verified to rated output.

4O3A Power Genius XL amplifier

Power Genius XL

The 100% ICAS duty-cycle, legal-limit (1500 W) 1.8-54 MHz SO2R amplifier. No/low output, LDMOS failures, ALC and protection faults, fan/thermal issues, and firmware-related problems.

4O3A product page ↗
Diagnostic-first · $95 diagnostic fee
4O3A Power Genius XL 3WAY

Power Genius XL 3WAY

Same legal-limit platform with integrated 3-antenna switching. We service the amplifier stages plus the antenna-switching and band-memory functions.

4O3A product page ↗
Per-unit estimate
4O3A Power Genius XXL Twin

Power Genius XXL Twin

TWIN dual-module platform delivering up to 3500 W / SO2R. Module-level diagnosis, hot-swap module faults, combiner and control issues, and full-power verification.

4O3A product page ↗
Per-unit estimate
Tuner Genius

Automatic tuner repair

High-power LAN-controlled automatic tuners - relay, matching-network, control, and connectivity faults brought back to spec.

4O3A Tuner Genius XL

Tuner Genius XL

High-power automatic antenna tuner. Relay and L/C network faults, sensing and tuning-algorithm issues, control-board and LAN connectivity problems.

4O3A product page ↗
Per-unit estimate
4O3A Tuner Genius Outdoor

Tuner Genius Outdoor (TGXL-O)

Feed-point-mounted LAN-controlled tuner. Weather-sealing, relay, and remote-control faults, plus full matching-range verification.

4O3A product page ↗
Per-unit estimate
Antenna Genius & station automation

Switching & control repair

The smart-switching and station-control heart of a 4O3A station - relay, RF-path, control-board, port, and network faults, for both local and remote operation.

ModelWhat we service
Antenna Genius 8x2+ V2Smart antenna switch, 8 antennas to 2 radios, 3000 W, LAN control - relay and isolation faults, RF-path issues, control-board failures, PTT interlock and network/app connectivity.4O3A product page ↗
Antenna Genius 8x1Smart antenna switch, 8 antennas to 1 radio, 3000 W, LAN control - the same relay, isolation, RF-path, control-board and network/app faults as the 8x2.4O3A product page ↗
OM Module16 dual-output relay expansion for Antenna Genius and Station Genius - relay, driver, and interface faults.4O3A ↗
Rotator GeniusSmart rotator controller with magnetic azimuth sensing - controller, sensor-interface, drive-output, and app-connectivity faults.4O3A ↗
Station ManagerProgrammable console for LAN/Internet control of Genius devices and transceivers - console, button/encoder, display, connectivity repair.4O3A ↗
Radio2LAN / CAT2LANLAN interface for RS-232 / CI-V control of radios, amps, rotators, tuners - port, level-conversion, and network faults.
Station Genius (legacy)Discontinued by 4O3A, but we still service existing units where parts allow - switching, control, and port faults.4O3A ↗

All automation repairs are per-unit estimates (Station Genius: evaluation-dependent, parts permitting).

Switches & splitters

Antenna switch & protection repair

From desktop A/B switches to tower-mounted high-power switches and lightning grounding systems - relay, isolation, weatherproofing, and control faults.

ModelWhat we service
8x2 Antenna SwitchHigh-isolation 8→2 switch - relay, isolation, and control faults.4O3A ↗
8xAB SwitchEight A/B relays in one box - per-section relay and control repair.4O3A ↗
AB SwitchSingle high-isolation A/B relay for matrix extension - relay and PTT faults.4O3A ↗
A50 Switch50 Ω termination for open combiner ports - load and switching service.4O3A ↗
Outdoor 6x1 CMCTower-mounted 6→1 switch with high-power CMC transformer - relay and weather-seal service.4O3A ↗
Grounding Switch GAS4KUAutomated lightning grounding/protection - sensing, relay, and control faults.4O3A ↗
Power Splitter PS3000RXSplitting/combining across 1-3 antennas - RF-path and control repair.4O3A ↗
1 Amp / 2 Radios (1A2R)RF + PTT router, one amp between two radios - switching-logic and relay faults.4O3A ↗
Reversible Switch RS3000Swap amp/antennas between two radios, plus the RS3000 control box - relay and interlock repair.4O3A ↗
Manual Antenna Controller S8Manual controller for Antenna Genius / 8x2 / PS3000RX - switch, encoder, and output faults.4O3A ↗

All switch and splitter repairs are per-unit estimates on the same open-book formula.

High-power filters & combiners

Filter, triplexer & combiner repair

High-power filtering and multi-station combining gear - insertion-loss, rejection, connector, and relay faults, with verification toward rated power.

4O3A Band Pass Filter Series XL

Band Pass Filter Series XL

High-power (4,500 W ICAS) 160-6 m band-pass filters. Insertion-loss and out-of-band-rejection issues, connector and fan-cooling service, and sweep verification.

4O3A product page ↗
Per-unit estimate
4O3A Triplexer Combiner HFC4500

Triplexer Combiner HFC4500

High-power 20/15/10 m triplexer letting three stations share one tribander at 4.5 kW. Filter-section, isolation, and connector faults.

4O3A product page ↗
Per-unit estimate
4O3A Triplexer Extender QPXC8

Triplexer Extender QPXC8

Combiner that extends the triplexer system for big-station setups. Band-routing, isolation, and connector repair.

4O3A product page ↗
Per-unit estimate
Beyond repair

Calibration & blueprinting

Two measurement-driven services for operators who want their gear verified to spec - or fully characterized on paper.

Calibration Service

We verify and bring your unit's key parameters back to the manufacturer's specification - power output, gain, bias, tuning, and filter response - using calibrated RF test equipment. You receive a calibration record listing the measured values and the spec they were set to. Ideal after a repair, before a contest, or as periodic maintenance on a high-value station.

Bench-rate · calibration record included

Blueprint Service

A full measurement characterization - a "blueprint" - of your specific unit. We sweep and document its actual RF performance (insertion loss, return loss / VSWR, rejection, gain, power, and more, depending on the device) and deliver a measurement report with the real data. It's both a verification of true performance and a baseline "fingerprint" you can compare against years later to catch drift or damage.

Per-device · full measurement report delivered

View an example filter report →

Beyond 4O3A

General RF repair

4O3A service is our focus, but the same bench and test equipment handle other gear too.

  • HF amplifier repair - solid-state and tube linears: no/low output, blown finals, bias, ALC, and protection faults.
  • Tuners, power supplies & alignment - brought back to spec with before/after readings.

What we don't take on: we do not repair transceivers or radios. Amplifiers, tuners, switches, and filters are what this bench is set up and calibrated for, and we would rather point you somewhere better than take on work we can't do to the same standard.

Tracked, every step

Whatever we repair, your ticket moves through clear stages with an email at each milestone:

Intakereceived → on bench
Estimatecreated → approved
Repairin progress → done
Returnshipped → delivered

Have a 4O3A unit that needs attention?

Open a repair ticket with your model, serial, and symptoms - we'll review it and send shipping instructions.